Description of steam injector:

A steam injector is a device that is powered by steam and is needed in modern engineering. It does not require electricity, has no moving or rotating parts, is simple in system, and works reliably, so it is used.

Steam injector structure - Introduction:

The steam injector structure mainly consists of two parts:

1. Spray nozzle: High pressure steam forms a high-speed jet through the spray nozzle. The shape and size of thespray nozzle are calculated based on the quality of the steam (superheated or saturated steam) and the pressure drop of the steam at the spray nozzle. When the pressure drop of the spray nozzle is above 45.5% of the initial pressure of the superheated steam. The saturated vapor is above 42.3% of the initial pressure. The nozzle is made into a Laval nozzle, otherwise the nozzle is conical, and the material used is 1Cr18Ni9Ti.

2. Steam injector - combined -: After the two streams of high and low pressure steam are uniformly combined in this pipe, the speed is reduced and the pressure is increased. So - there -, -, and the last three - have different effects. The shape is different, and its size (diameter and degree) is designed based on the total flow rate to ultimately synthesize the required pressure of steam. The component connecting the two is called a steam chamber, which maintains a reasonable distance between the two components and has a certain space. The material of the steam injector is made of 1cr18Ni9Ti or 20 # - carbon steel.

Equipment operation:

Steam jet water heaters and vacuum heaters have different operating requirements, but the temperature of the booster is high and the pipes should be warmed up. At the beginning, a small amount of low-pressure steam enters the steam chamber of the jet booster and is discharged into the steam supply pipe for heating. According to the factory regulations, the pipes are heated in stages. As the low-pressure steam increases, the high-pressure steam valve is gradually opened to form a supply pressure at the outlet, which is adapted to the steam consumption.

Steam injector installation:

1. This equipment is installed in pipelines and high-pressure steam pipes. The low-pressure steam pipe and heating pipe are respectively connected to the flange of this component, and the flange is from the Ministry of Chemical Industry.

2. Vacuum type steam injectors (such as shaft seal air extractors) can be fixed on walls, columns, and then connected to relevant pipes due to their smaller size.

3. Equipment should be arranged from top to bottom or horizontally in the direction of steam outlet, and avoid being arranged from bottom to top.

Material of steam injector -:

Steam injectors are made of materials such as carbon steel, stainless steel, and ordinary cast iron. They are stable, easy to install, and do not require high-level installation. They can be installed on flat ground. Each type of steam injector can be vacuumed by equipped with corresponding centrifugal water pumps, and can be used in parallel.

Scope of use of steam injectors:

There are the following types of steam injectors:

1. Steam injector booster type:

High temperature and high pressure steam with high energy is attracted by the high-speed jet of the nozzle to produce low-pressure steam at the required temperature and pressure for the synthesis process. This is a more energy-efficient form required by the process (compared to temperature and pressure reducers), and it is also more convenient. There is also a type of equipment called a secondary steam recovery device.

2. Steam jet hot water type:

By using steam jet suction, a certain amount of cold water is heated to the desired temperature and delivered to the desired location, which can be used for heating and domestic water.

3. Steam injector vacuum type:

By steam jet, the air inside the container is extracted to provide a certain vacuum. Like the steam turbine shaft seal extractor, it prevents the steam turbine from flowing outward and recovers heat and working fluid. For example, using a type of circulating water pump to suction and vacuum to attract low-level water flow.

4. Steam ejector:

The steam jet air extractor is used on the steam turbine shaft seal air recovery device, thereby eliminating the loss of steam at the end of the steam turbine shaft seal, improving the thermal economy of the unit, improving the on-site environment, and preventing air from entering the bearing lubricating oil due to excessive time of the shaft seal air. This is an important measure to prevent oil water content and high shaft seal temperature-- The thermal design uses a steam jet extractor for the sealing steam condenser, reducing the loss of steam in the turbine shaft seal. It also uses the heat of the gas to heat the condensate, recover heat and working fluid, improve the thermal economy of the unit, and prevent oil water ingress and bearing high temperature accidents caused by excessive gas from the shaft seal entering the bearing lubricating oil.. Work principle: Working steam enters the nozzle, expands and accelerates into the mixing chamber, forming a high degree of vacuum in the mixing chamber, which extracts the gas and vapor mixture from the condenser. After mixing, it enters the expansion tube, where the pressure is slightly higher than the pressure. After condensing through the cooler, some steam condenses into hydrophobic water and returns to the condenser, with a small amount of gas and vapor mixture discharged into the gas. The steam jet extractor has a low extraction rate, but its structure is simple, and it can recover the heat of working steam and condensed water, so it is applied.

The purpose of fly ash sampler

The purpose and function of The fly ash sampler produced by Lianyungang Lingdong Electromechanical Equipment Co., Ltd. is that The carbon content of boiler fly ash is an important indicator reflecting The combustion rate of coal-fired boilers in Thermal power plants.

Installation and working engineering of coal powder sampler

The installation and operation of The coal powder sampler and mobile coal powder sampler of Lianyungang Lingdong Electromechanical Equipment Co., Ltd. drill holes on The flue, extend The sampling tube into The flue, and make The sampling head face The direction of The incoming smoke flow.

steam water heat exchanger

HR high water and steam water heat exchanger is a type of heat exchange equipment that uses The heat of waste gas and wastewater to heat cooling water. Heating water enters The equipment from The side of The pipe box and passes through a heat exchange surface composed of high 304 stainless steel tubes. There are four processes in total to transfer heat to The heated water, etc.

Tube replacement of tubular oil cooler

When purchasing a column type oil cooler for tube and core replacement, The cooling area should be informed. The cooling forms are divided into LY type light tube (for use) and LYC type fin type. Stainless steel tubes are generally selected for heat exchange and cooling, and purple copper, brass, and titanium tubes can also be selected as heat exchange components according to user needs.

steam -seal cooler

The role of a steam -seal cooler is to make The tram from The steam turbine slightly negative pressure, so that The auto continuously enters The auto seal cooler through The auto pipeline and condenses it into water for The boiler to use it.

steam manifold

Our company's main products include: distribution cylinder, collection cylinder, water distributor, water collector, steam header, and oTher water tanks, oil tanks, air tanks, cylinders, and oTher equipment. The distribution cylinder, also known as The distribution drum, is The main supporting equipment for steam boilers, used in industries such as power generation, petrochemicals, steel, cement, and construction.

Replacing The tube of The shaft seal heater

Manufacturer of shaft seal heaters, also undertaking pipe replacement and renovation of shaft seal heaters, replacing copper pipes, stainless steel pipes, boiler pipes, etc. According to customer needs, The replacement, repair, installation, and restoration of The relevant shaft seal heater pipes must be carried out. The original equipment must be sent to our company for pipe bundle replacement.

Oil cooler tube replacement and maintenance

We are a manufacturer of oil cooler tube replacement and maintenance. We undertake various types of tube coolers, condensers, oil coolers, chillers, air coolers, condensers, and oTher heat exchange and cooling tube replacement and renovation projects. Change The material of The pipes, such as copper pipes, stainless steel pipes, titanium pipes, etc.

Assembly and installation of oil injectors

The oil supply and lubrication oil injectors are completely identical in structure, mainly composed of orifice nozzles, diffusion tubes, sleeves, filters, etc.

steam seal heater tube replacement and renovation

The steam seal heater adopts a horizontal U-shaped surface heat exchanger for pipe replacement and transformation. The pipe material is stainless steel pipe, and in addition to expansion joint, The pipe also needs to be sealed and welded with The pipe plate; HSn-70-1 tin brass is also used and fixed on The tube plate by expanding The tube.

• Previous：Calculation of cooling area of sampling cooler
• Next：The basic principle of lubricating oil system injectors